How to Replace a Kia Sportage Replacement Key
For a variety of Kia models keys, there is a built-in keyless entry system. This key usually resembles the remote control and can be replaced with a fresh one from an Kia dealer or locksmith.
Key fobs can fail to function due to a number of reasons, including the battery being dead, worn-out buttons signals, signal interference or water damage. Here are some suggestions to assist you in getting your Kia sportage replacement key working again.
How to replace the remote key or smart key
The battery inside your Kia's smart key will eventually need be replaced, whether it's a remote as well as a push-to start key or a regular metal key that doesn't contain transponder. This is especially the case if your car displays a message telling you that the remote or smart keys have low battery power.
Luckily, this is quite simple to do. In order to replace the key fob battery remove the mechanical key from the slit at the back of the key fob. Then break the cover. Inside the key fob will be the small screw that holds the battery in the correct position. Remove the old battery by removing the screw with the help of a small screwdriver. Insert the new battery and close the cut on the key fob.
When the key fob is equipped with a fresh battery check it by pressing the lock and unlock buttons. It's okay when the doors lock or unlock as expected. You can now use Kia's hands-free lock/unlock function when your fingers are cold or you have to go on errands around Brandon.
Note: Certain key fobs could need to be programmed (transponder chips or smart keys). This requires a special programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) don't require programming. If your key has to be programmed again, you will need to be aware of the number that is stamped on the key code tag and save the number in a secure place.
How to replace the battery
If the Kia key fob is unable to respond when you press the lock/unlock button, it is most likely that the battery is not fully charged. A battery that is not functioning properly could cause other issues such as the check engine light flashing on or a delay in cranking the engine. Fortunately replacing the key fob battery is a relatively easy DIY project that requires only a few tools.
Make sure you turn off your vehicle and shut the doors before you begin. Find the small metal or a plastic piece at the bottom of the key fob. Then, jiggle it until the key falls out. You can then insert this key into the door handle of the driver to unlock your car.
To replace the key fob's battery, remove the cover at the rear and use a plastic bar tool to loosen the latch that holds the black negative battery cable. Remove the old battery and then orient the replacement battery to ensure its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid breaking or bending the steel contacts.
After the new battery has been installed after which you turn the key fob off and on in the ignition repeatedly until the door locks cycle. You can then test your Kia's keys fob again to make sure it's working as intended.
How do you replace a smart keys
Depending on the model of your Kia Sportage, you may have an ordinary key fob or a smart key. The smart key is equipped with an embedded mechanical key blade while the standard key fob does not. Both key fobs are equipped with batteries that eventually need to be changed. Fortunately, this is an easy process that takes only two minutes.
Make sure you turn off your Kia and stand on a level and well-lit surface prior to you begin. Keep in mind that there are tiny components inside the fob that could be removed if not careful.
The first step is to find the small release button that is located on the backside of the fob. This will either be an oval silver button or a rectangular slot. You can open the key fob by pressing the button.
Once the key fob is removed, you can remove the battery that was in it. The new battery is C2032, and can be bought through the internet or at a local auto parts shop. Once you're done, your key fob should be able to lock or unlock and start your vehicle, even if it isn't running.
How do I replace a mechanical key
The Kia key fob is a fantastic option that lets us lock and unlock our vehicle with the touch of the button. As with all devices, the Kia key fob can have issues at times. There are G28 Car Keys to fix these problems and keep your key fobs in good working order for an extended period of time.
A dead or weak battery is among the most common problems. This can cause the device to stop working completely or stop working at times. If this is the case, replace the battery with an entirely new battery.
If this isn't enough to solve the issue, use an ordinary screwdriver with a flat head to push the fob's plastic casing open. Be careful not to scratch any internal components or scratch the plastic. Once open, carefully remove the battery that was removed and replace it with a new one.
Close and open the door with the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the key fob to verify that it's working correctly. Contact a dealer or a locksmith to fix the issue in the event that the key fob is not working. To avoid future lockouts, ensure you purchase an emergency key that can work on all door and trunk cylinders.